- NETBOTZ SERIAL CONFIGURATION UTILITY INSTALL
- NETBOTZ SERIAL CONFIGURATION UTILITY PASSWORD
- NETBOTZ SERIAL CONFIGURATION UTILITY DOWNLOAD
- NETBOTZ SERIAL CONFIGURATION UTILITY MAC
For example:Ĥ) Use apc for both user name and password.ĥ) Use this command to configure network settings (text in italics indicates a variable.)įor each variable, type a numeric value that has the format. For the IP address defined in step 1, use one of the following commands:ģ) Use Telnet to access the Rack monitor 250 at its newly assigned IP address.
NETBOTZ SERIAL CONFIGURATION UTILITY MAC
NOTE: Look for the MAC address on the bottom of the Rack Monitor 250 or on the Quality Assurance Slip included in the package.įor example, to define 156.205.14.141 as the IP address of a Rack Monitor 250 with 00 c0 b7 63 9f 67 as its MAC address, use one of the following commands:Ģ) Use Ping with a size of 113 bytes to assign the IP address defined by the ARP command. The Rack Monitor 250 restarts to apply the changes.įrom any computer on the same network as the Rack Monitor 250, you can use ARP and Ping to assign an IP address to the Rack Monitor 250, and then use Telnet to access its command line interface and configure the other TCP/IP settings.Īfter the Rack Monitor 250 has its IP address configured, you can use Telnet, without first using ARP and Ping, to access that Rack Monitor 250.ġ) Use the MAC address of the Rack Monitor 250 in the ARP command to define the IP address. Tcpip -i yourIPaddress -s yourSubnetMask -g yourDefaultGatewayįor example, to set a system IP address of 156.205.14.141, a Subnet Mask of 255.255.255.0, and a default gateway of 156.205.14.1, type the following command and press ENTER:
NETBOTZ SERIAL CONFIGURATION UTILITY PASSWORD
NOTE: Username and password may have been changed if the appliance was already configured.Ħ) Use this one-line command to configure network settings (text in italics indicates a variable that needs to be entered in format ). Plese refer to knowledge base FA381275 for instructions on installing the driver.Ĥ) Press ENTER, repeatedly if necessary, to display the User Name prompt.ĥ) Use apc for the user name and password.
NETBOTZ SERIAL CONFIGURATION UTILITY INSTALL
NOTE: If you are unable to access the appliance using the console port, you may need to install a serial-to-USB vritual COM port driver. 3rd party terminal emulator like HyperTerminal TM, PuTTy, or Tera Term) and configure the selected port for 9600 bps, 8 data bits, no parity, 1 stop bit, and no flow control. NOTE: If the utilit does not find any NMCs, you can increase the total search time value within the Settings menu > Find And Setup Device Off Network.Ĭontact your network administrator to obtain the IP address, subnet mask, and default gateway for the Rack Monitor 250.ġ) Select a USB port at the computer, and disable any service that uses that port.Ģ) Connect the provided USB A-USB mini B configuration cable from the selected port on the computer to the console port on the Rack Monitor 250.ģ) Run a terminal program (e.g. NOTE: When installed, the utility is available through the Windows "Start Menu" option.Ĥ) Click the tab for Find And Setup Device Off Network.Ħ) Select the Management Card from the MAC address table on the left.ħ) Enter the IP address, subnet mask, and gateway address.
NETBOTZ SERIAL CONFIGURATION UTILITY DOWNLOAD
You may need to refer to your DHCP server to find out what IP address the Rack Monitor 250 obtained.Ģ) Within the featured downloads section download the Network Management Device IP Configuration Wizard.ģ) Run the downloaded executable file and follow the prompts to install the application. The IP address should be obtained automatically once the NetBotz 250 is connected to a network that has an active DHCP server. The Default boot mode is DHCP only - with DHCP Option 43 Vendor Cookie NOT required to accept DHCP offer. Web Interface (Adjusting already configured TCP/IP settings).Remote Access to Command Line Interface.NetBotz Rack Monitor 250 (all firmware versions)
NetBotz Rack Monitor 250 (NB250/NBRK0250) Process for configuring network settings (TCP/IP) on a NetBotz Rack Monitor 250.
0 kommentar(er)
